您现在的位置：网站首页 > 产品展示
产品展示- 自动多刀片旋切机
-
-
部件说明① 报警灯 alarm light② 停止指示灯 stop light③ 停止按钮 stop button④ 调速器 speed controller⑤ 启动按钮 start button⑥ 电源指示灯 power light⑦ 开盖手柄 open the handle⑧ 石料夹紧旋转阀 the stone clamping rotary valve⑨ 挂档旋转轮 the gear rotating wheel⑩ 水管 water pipe＆#9322; 主轴 principal axis＆#9323; 石料夹头 stone fastening clamp＆#9324; 接触器 contactor产品技术参数品 名：自动多刀片旋切机参 数：输入电压：AC 380V电机功率：4KW主轴转速：900r/min外观尺寸：长110cm×宽90cm×高105cm（±5cm）Product's Technical ParametersName：Rotary cutter machineArguments：U：AC 380VP：4KWRev：900r/minSize: 110cm (L)×90cm (W)×105cm (H)（±2cm）操作说明二、将锯片和垫片依次装入＆#9322;主轴上，并锁紧；
三、将石料卡入＆#9323;石料夹头；将⑧石料夹紧旋转阀卡紧；四、打开⑩水管水源；五、按下⑤启动按钮，启动电源；六、打开④调速器，根据石料硬度调节进料速度；七、当石料切至旋切机最大半径时，调节⑧石料夹紧旋转阀触动＆#9324;接触器，机器自动停止，①报警灯亮起；八、取出石料。九、当⑨挂档旋转轮推入里面时，表示挂档，自动进刀；拉出时，表示空挡，可手动调整石料前后位置。当开始切料时，应将⑨挂档旋转轮推入里面，正常工作。Operating instructions1. Power supply is switched on;2. The blade and gaskets are arranged on ＆#9322;the principal axis, and lock;3. Put the stone into the ＆#9323;stone fastening clamp; lock ⑧the stone clamping rotary valve;4. Open ⑩the water pipe water;5. Press ⑤the start button, start power supply;6. Open ④the speed controller, according to stone hardness regulating feeding speed;7. When the stone cutting reach the rotary cutter machine maximum radius, adjust⑧the stone clamping rotary valve touches ＆#9324; contactor, the machine will stop automatically, the alarm light;8. Remove the stone.9. when ⑨the gear rotating wheel into the inside, said gear, automatic feed; out,said neutral, manual adjust the location of stone. When cutting, should be ⑨the gear rotating wheel into the inside, the normal work.注意事项：1、设备用电必经漏电开关！！！2、使用设备前必须接地！！！4、请您在使用本机前，认真阅读使用说明和注意事项。Note:1, The equipment must be pass through the leakage switch!!!!!!!!!!!2, Before using equipment must be grounded!!!!!!!!!!!3, If fault, cannot be not tear down by yourself, should be a professional inspection, should be handled by professionals to check!!!!!!!!!!!4, please before using the machine, read the instructions and matters needing attention.5, before use, please check whether the power supply you use is consistent with the machine, to ensure good grounding device. - [返回]