您现在的位置：网站首页 > 产品展示
产品展示- 超声波雕刻机
-
-
部件说明① 升降手柄 lift lever② 喇叭头 flared head③ 针头 syringe needle④ 水管 water pipe⑤ 重力杆 gravity lever⑥ 超声波功率调节 ultrasonic power regulation⑦ 水泵 water pump⑧ 超声波电流表 ultrasonic current meter⑨ 电源开关 power switch⑩ 水泵开关 water pump switch＆#9322; 超声波开关 ultrasonic switch＆#9323; 指示灯 lamp＆#9324; 超声波频率调节 ultrasonic frequency regulation
产品技术参数品 名：超声波雕刻机参 数：输入电压：AC 220V输出功率：2500W外观尺寸：长55cm×宽55cm×高150cm（±2cm）Product's Technical ParametersName：Ultrasonic engraving machineArguments：U：AC 220VP：2400WSize: 55cm(L)×55cm(W)×150cm(H)（±2cm）一、将机头线、风扇线、水泵线、电源线插入主机后方对应位置；将模具焊接在③针头上；二、将③针头和②喇叭头连接，锁紧；
三、将石料放入③针头下方的升降台上，对准；四、将⑤重力杆调节至适当重力，放开；五、打开⑨电源开关；六、打开⑩水泵开关；七、调节⑥超声波功率调节至所需位置；八、打开＆#9322;超声波开关；九、调节＆#9324;超声波频率调节至适当位置，＆#9323;指示灯熄灭；十、③针头越粗，⑧超声波电流表电流越大。十一、水泵电机部分请注意防水。十二、水桶水位距水桶上沿5cm，不能过满。十三、金刚砂加入3~4kg。Operating instructions1. To the handpiece wire, the fan wire, water pump wire, the power wire inserted into the mainframe corresponding position; weld holing needle on ③syringe needles;2. Connect ②flared head ③ syringe needle, lock;3. Put gem stone at the bottom of the lifting platform under ③syringe needle, alignment;4. To adjust ⑤gravity lever to proper gravity, let go;5. Open ⑨the power switch;6. Open ⑩ water pump switch;7. Adjust⑥ultrasonic power regulation to the in place;8. Open ＆#9322; ultrasonic switch;9. Adjust ＆#9324;ultrasonic frequency to the in place; ＆#9323;lamp go out;10. The needle③ is bigger, ⑧ultrasonic current meter current increasing.11. Please note waterproof water pump motor parts.12. The water level along the 5 cm away from the bucket, bucket can't too full.13. Emery added 3~4kg.注意事项：1、设备用电必经漏电开关！！！2、使用设备前必须接地！！！3、故障时，不可自行拆卸，应由专业人士检查处理！！！4、请您在使用本机前，认真阅读使用说明和注意事项。5、使用前，请检查您所使用的电源是否与本机相符，确保有良好的接地装置。Note:1, The equipment must be pass through the leakage switch!!!!!!!!!!!2, Before using equipment must be grounded!!!!!!!!!!!3, If fault, cannot be not tear down by yourself, should be a professional inspection, should be handled by professionals to check!!!!!!!!!!!4, please before using the machine, read the instructions and matters needing attention.5, before use, please check whether the power supply you use is consistent with the machine, to ensure good grounding device. - [返回]